nawerfb.blogg.se

1. #Kenwood tk 880 programming ham radio install#
2. #Kenwood tk 880 programming ham radio manual#
3. #Kenwood tk 880 programming ham radio Pc#
4. #Kenwood tk 880 programming ham radio series#

Set PTT Delay to Trunking if you are on a trunking system Console and Speed vary on your application Note: Console needs to match programming the Modem Parameters PTT Delay: Trunking COR Polarity: Active Hi On-Air Polarity: Active Hi Console: 1 Speed: Set COR and On- Air Polarity to High See the Pyramid 2016 service manual for further Pyramid Console software information. To access the Modem Parameters menu, select Configure from the pull down menu.

#Kenwood tk 880 programming ham radio series#

The figure below shows how a typical Pyramid Console software would be set up when connected to a 2016 and TK-x80 series radio.

Consult your RasTrac manual for more information.

#Kenwood tk 880 programming ham radio Pc#

Typically, the parameters are set in the Pyramid Console software, and then automatically sent to the If you are using Manning NavComp Inc s RasTrac MX software for you console interface, all configuration is done within the RasTrac I/O processor that runs on your PC simultaneously with the RasTrac mapping software. 3Ĥ Programming the Pyramid 2016 Programming of the Pyramid 2016 base modem is done through the console interface. More programming instructions are available in the 2012/Merlin Service Manual. Chose the format to fit your application. There are three signaling format cho ices. From the Data pull down menu, select your Data Format in the Format Screen. Note: Console needs to match programming the 2016 Console Software Vehicle #: 100 ( ) Base #: 1 (1-4) PTT Delay: 0.5 S (.1-2.5) Retries: 3 (0-9) Trunking mobile Yes Sequential Status No ANI on mobile PTT No Enable Time Stamp No COR Polarity High On Air Polarity High I/O Pin 9 Output Mute Enable Turnking Mode if applicable.

Vehicle # and Base # will vary with your application. From the Data pull down menu, under the System Data screen, program the unit as shown the figure below. Start running the Pyramid 2012/Merlin programming software on your PC.

#Kenwood tk 880 programming ham radio install#

If you have not already done so, install the programming software on to your PC by following the instructions in the 2012/Merlin service manual. Programming the Pyramid 2012/Merlin The mobile data terminal needs to be programmed to accommodate the polarities of signal that the Kenwood mobile will provide it. To get a copy of version 8050 firmware please contact your Kenwood dealer. Also, you will need a copy of the Pyramid 2012 programming software and FY-1 programming cable to program the Your TK-x80 radio MUST be programmed with firmware version 8050 or newer for mobile data applications. 1 Programming Instructions for: Kenwood TK-880, 980, 981 W/ KCT-19 Option Connector For use with: Pyramid Communications Model 2012/2016/Merlin Revision D November 21,Ģ Introduction.3 Programming the Pyramid 2012/Merlin.3 Programming the Pyramid Programming the Kenwood TK-x80 Series Mobile.5 Radio Format.5 Programming Optional Features.5 Programming the Logic Signalling.6 Programming the Talk Group information for a 2012/Merlin MDT.6 Defining a Talk Group for Data Use.7 Programming the Talk Group information for a 2016 Base.8 Connecting the Pyramid to the Kenwood TK-x Connecting the 2012/Merlin MDT to the TK-x80 radio Jumper Settings in the 2012/Merlin Connecting the 2016 base to the TK-x80 radioģ Introduction Before you begin, you will need to have a copy of KPG-49D and programming cable available to program the mobile radio.